3
votes
Is Behringer C-1 mic good enough for foley recordings for the price?
To be honest any mic can do Foley, I've seen Foley done with an sm57 which is historically an instrument mic. Foley has much more to do with technique than what mic you are using, 80% of Foley is the ...
- 252
2
votes
8 channel pass through on Behringer XAir XR18
This is a non-starter I'm afraid.
Your best bet is to simply acquire or make 8 passive splits and split the input channels prior to the XR18. Send the splits to the FOH/Monitor engineer.
- 8,900
2
votes
How to connect a condenser microphone directly to a PC (without a mixer)
Just get a basic Behringer USB preamp interface that supports Phantom power. Then there's a direct connection from the microphone through the preamp into the computer. Job done. Impedance isn't a ...
- 8,900
2
votes
Issues with mix-minus setup on Xenyx Q1002USB with dbx 286s
a. Make the setup work with the new balanced audio cables and restore the fidelity of the audio.
You don’t have new balanced audio; you have unbalanced stereo going into a balanced input which does ...
- 1,080
2
votes
Behringer x32 Out 1-16 levels
I think so, yes. Route both L and R to one matrix bus, and assign that to Out 1.
That depends on how you provide a signal to the Out port: Out 1-16 is just the output assignment. You set the volume ...
- 1,738
2
votes
Online sound is always low
By using an aux send you can mix the volumes of each channel to the proper level (also labeled as Bus 1-6 on the XAir app)
- 1,080
2
votes
For optimal 3-way sound: should passive speakers be connected to my amplifier/mixer, or to the crossover of an active subwoofer?
Are the subwoofer crossover outputs indeed for passive speakers? Or are they intended for active speakers or amplifier?
I would expect an active subwoofer to have the crossover at line level since ...
- 21
2
votes
Move Faders X32 Behringer Console
The X32 does not support user-defined fader banks. You cannot change them.
The first page will always have Channels 1–16, the second page always Channels 17–32, the third page always the Aux Returns, ...
- 151
2
votes
Accepted
Recording from Behringer X32 into Reaper captures only inputs, not channel outputs
On the X32:
Press the Routing button
Go to the Card Out tab
Select the channels you want to record. If you want to record the outputs, scroll down and you'll find Out 1-8 and Out 9-16.
If you want ...
- 1,738
2
votes
Recording from Behringer X32 into Reaper captures only inputs, not channel outputs
You are using direct outputs for each channel which sends the signal to the DAW before the EQ or any other processing. If you want to record a live performance, rather than multitrack recording from ...
- 1,080
1
vote
Move Faders X32 Behringer Console
in fact you can move around inputs
select the channel you want to change
goto Config and change the source
in your example
CH1 source = AUX1
1
vote
Accepted
Why is the recording level on my DAW different than on my audio interface?
There are different dB scales that gives different readings.
Looks the meter on your audio interface is analog so the signal strength will then be given in dBU. You can tell because the scale goes ...
- 161
1
vote
Accepted
Behringer X32 - USB input to "Main Mix"
To make sure you've got the USB interface set to 32 channels:
Setup menu, Card tab:
set to 32 in/32 out.
To connect the USB input to the 32 channels:
Routing menu->Home tab:
this is a list of ...
- 1,738
1
vote
How can I reduce hi-fi amplifier latency?
If the input is analog but you still get a delay, it's likely the amplifier does an AD conversion on its inputs. In that case, you'd need to use a different amplifier you are certain is analog.
- 1,738
1
vote
Issues with mix-minus setup on Xenyx Q1002USB with dbx 286s
I replaced the unbalanced cables with 1/8" to 1/4" cables, thinking that would fix it.
That's still an unbalanced cable. Your PC output is unbalanced, any cable connected to it will be unbalanced.
...
- 1,738
1
vote
Accepted
8 channel pass through on Behringer XAir XR18
The way to route channels 7 and 8 to the mains is to pan them on to each side and push them up like you were mixing FOH for a show. Set the aux channels to pre-fader and then turn them up in the aux. ...
- 111
1
vote
Connecting Playback Audio Source to S16 connected to X32
No, that won't work. There's a USB port on the S16 but according to the manual, it's for firmware updates only.
A long USB cable might be possible, but you'd have to test that. For cable lengths ...
- 1,738
1
vote
Behringer C1-U Microphone Static Noise In Background
OK that sound is mains frequency induction into the microphone or the cable. It can be eliminated by ensuring you have a correctly balanced cable between your interface and microphone. If, once ...
- 8,900
1
vote
Weird pops and cracks in my Reaper input?
I had this same issue and what would recommend and what worked for me is make sure the two boxes by the bottom are checked when setting up your driver in reaper! Especially the (Ignore asio reset ...
- 11
1
vote
For optimal 3-way sound: should passive speakers be connected to my amplifier/mixer, or to the crossover of an active subwoofer?
I think the manual is pretty clear. Stereo mixer output into the subwoofer, stereo output from the subwoofer into either active speakers or a stereo power amp with passive speakers. The subwoofer ...
- 11
1
vote
How to connect Behringer mixer to Macbook Pro?
Behringer make several small and simple USB audio interfaces like their U-Control series. And versions with more features like the U-Phoria series, etc. Of course there are many other makers of ...
- 1,869
1
vote
Accepted
How to connect Behringer mixer to Macbook Pro?
This mixer doesnt support usb connectivity, youll need a usb interface for that.
After you get a usb interface you can route your mac to output the channels from your usb interface outputs and then ...
- 1,582
1
vote
New Behringer C-2 microphone malfunctioning
these are interchangeable capsules. Try switching the capsules around and attempt to further isolate the fault to the body or the capsule. This will also be a chance to give the capsules connection ...
- 8,900
1
vote
Accepted
Recording 2-6 lav mics to a Mac with a Behringer UMC1820?
1) you will need something to manage the inputs. I only know of software solutions. I use Logic.
2) I don't have experience with the UMC1820 but I have their XAir x18 and it's a single device with ...
- 134
1
vote
How can I send internal FX to monitors on a Behringer mixer?
I just wanted to add a bit more details to Michael's answer regarding how to make it work with the UFX1204. I know it's 5 years later, but the manual doesn't properly address this trick.
First, send ...
- 111
Only top scored, non community-wiki answers of a minimum length are eligible