I have a stereo mix file at about 0 dbfs. When I put a high pass filter and cut below 30Hz it boost the signal +3db up. Is this normal? I tested it with different filters (plug ins only) and I had the same result. DAW was ableton but I remember I had the same issue with Pro Tools in the past.

  • If the simple boost in the lows from a HPF is clipping your channel the input gain of the channel is WAY to high. I understand how much energy is in the low end but really... Typically with proper gain structure you should have 12db or so of headroom on a channel so that there is room for transients and volume peaks. Running at peaking levels (0 DBFS) is madness. If this channel needs that level to be heard in context of the entire mix then the whole thing is too loud pull the whole mix back an equal ammount on each channel (say even 6db) and you will be much happier.
    – skids89
    Commented Sep 16, 2014 at 22:19

3 Answers 3


It is not inevitable, but nor is it surprising – yes, it would call it normal.

"Low cut" doesn't specify what the filter does exactly. Better models will either give a whole bunch of possible settings, or specify clearly the characteristic. If nothing is specified, the filter will generally be either

  • A first-order IIR (aka HP6). The advantage of this simple design is that it never boosts the total peak level: the filter simply follows the signal as-is, disregarding high-frequency peaks. So evidently this is not the design you're dealing with – indeed it wouldn't be much use either, since these filters have a very shallow cutoff (6 dB/8ve): set at 30 dB you'd scarcely notice any difference, and set to higher frequencies you'd affect also the desired bass range.

  • A resonance-free second-order IIR would be simply two of the above in series. That increases the cutoff steepness at low frequencies, but it still leaves a vast range where the signal is attenuated feebly.

  • A second-order Butterworth filter (aka HP12) mitigates this problem: it adds a slight resonance peak at the "knee" of the filter, not so strong that the signal is actually boosted anywhere, but a resonance it is nevertheless. This is most likely the cause of your issue.
    To understand why the peak level increases even though the filter does not boost any frequencies, you need to consider the phase relations: different frequencies are shifted by different "angle". Perhaps easier to understand: like the first-order IIR (actually, that can also be called first-order Butterworth), it follows the signal shape, but to avoid the "cutoff knee", the Butterworth2 "echoes" oscillations in that range. Therefore, short bursts can come out with higher amplitude (though never higher RMS).

  • Butterworth filters of higher order have basically the same issue, only worse; same goes for Chebyshev-, Cauer- etc. filters. I don't think those are used in any widespread filter plugins.

  • Bessel filters are specifically designed to minimise overshoot/phase distortion. But even they don't completely remove it. Indeed this isn't possible with analogue filters other than LP6-cascades!

  • What is needed for zero-overshoot without a big filter knee: add some resonance, but with "symmetric" character. This is only possible if the filter can look "forward in time". Which isn't possible in live sound, but certainly in digital recording. Note that this will also cause "inverse reverb" artifacts, i.e. you might be able to hear sounds in the recording before they actually occur – mostly an issue for phase-linear brickwall FIRs. Those can literally cut away all frequencies below 30 Hz, but this will severely mutilate the time-domain of pulses, with tens of milliseconds of "pre-smearing". (Brickwall FIRs are an essential part of proper resampling though).

  • Something of a ideal compromise is offered by Gaussian filters. These are phase linear with no overshoot, have pretty steep cutoff, and yet largely preserve the shape in time-domain. This is the filter type preferred by well-designed phase-linear EQs, and would propably the best fit for your problem.

Note that all that phase buzz is only relevant for the peak level. Loudness is in fact far more accurately described by RMS, which doesn't consider phase. The only reason peak level is relevant is that today's standards (still?) alas have a cap on peak, not on RMS or actuall loudness. It is this fact that's largely responsible for the loudness war. I recommend you look more at RMS levels than peak, except in the final mastering stage.
Indeed I generally prefer IIR filters despite their phase distortion, because they tend to have better or at least more predictable transient response. A second-order Butterworth high pass is just fine, simply apply it before the final compression/limiting stages. That will probably sound better anyway, because the compressors won't need to care about subsonic artifacts (which can cause unpleasant pumping / fluttering).

(Phases are also relevant when EQing different mics that have bleed signals of the same source, but I don't think that's an issue in your application.)

  • Very nice presentation! Could you give me some IIR filters plug in recommendation and others that uses Gaussian technology that you may know?
    – ik-Janni
    Commented Sep 17, 2014 at 13:29
  • @ik-Janni: as I said, Gaussian filters cannot be implemented in IIR / analogue circuits. You need to use FIR – the problems of which, honestly, I think usually outweigh the benefits. But for a start, try ReaFIR. Commented Sep 17, 2014 at 13:47

I have wandered about it a while back while using a low cut eq in logic, using a Linear Phase EQ instead of a regular eq solved this mystery.

Unfortunately, I don't know the theoretical explanation behind it but I suspect that a regular eq can create unwanted phase artifacts and hence those picks in your signal.

  • This is well observed. I explained the theory in my answer. Commented Sep 15, 2014 at 12:07
  • Yes you are both right! Putting a linear phase mode can solve the problem. But sometimes slightly change the color of the sound. It depends the area and the attack of the sounds. I 've noticed that waves SSL G-Equalizer doesn't give this boost and maintains a good sound.
    – ik-Janni
    Commented Sep 17, 2014 at 12:51

Could it be the filter resonance?


  • It sure is technically resonance, but not in the sense that any frequencies are actually amplified. Commented Sep 15, 2014 at 12:23

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.