Will connecting several mic cables together impact the quality of the recording? Obviously with every additional cable there's an added risk of a loose connection, but assuming my cables and connections are good, is there a reason to avoid this?

4 Answers 4


Every junction creates a point of high resistance, and alters the signal negatively. I don't know to what extent this affects audio quality, but in general it's best to use a single cable (barring the need to boost the signal power if the distance is really long).

  • 2
    With signal cables (as opposed to power cables) resistance is not an issue (capacitance is much worse). Of course, any connector brings mechanical issues that are worth attention, so it's better not to chain them.
    – Agos
    Dec 15, 2010 at 16:15
  • 1
    The resistance of the connectors is completely irrelevant. The output impedance of your mic is at least 100 ohm, and the load is at least 1.5 kΩ. No number of 0.1 ohm connectors is going to affect anything. The real problems with connectors are corrosion or contamination on the surface that cause distortion, the reliability of the connection when it gets stepped on, etc. So decreasing the number of points of failure is still good advice.
    – endolith
    Sep 11, 2012 at 14:03

While this is basically correct, and I know a few engineers that want to keep cable length as short and clean as possible, in my opinion the quality you lose by connecting two cables together (when good quality XLR cables with balanced signal are used) is of very little significance compared to the type of pre-amplifier you use and the rest of the equipment.


My experience has been that chaining cables together tends to raise the noise level, thereby reducing the signal-to-noise ratio. I try to avoid it whenever I can. It seems to get worse if I'm using an unbalanced cable or a poorly shielded cable. I haven't observed any difference using well-shielded balanced XLR cables.

However, use your ears, and your level meters - try it with just one cable, then try it with a chain of cables. See if you can hear a difference or see that the noise level raises. If you can clearly discern a difference, then you should avoid using such a chain.

  • What do you mean by "noise" in this case? Interference? Hiss? Hum?
    – endolith
    Sep 11, 2012 at 14:05
  • @endolith All of those would be correct, although I was particularly thinking of hiss and hum when I wrote the answer.
    – Warrior Bob
    Sep 11, 2012 at 15:45
  • 1
    Hmm.. adding more connectors shouldn't have any effect on hiss.
    – endolith
    Sep 11, 2012 at 16:03
  • @endolith I may be using the term "hiss" incorrectly if it has a precise technical meaning. When I've tried chaining several cables together I've observed an audible increase in some kind of broadband noise, similar to white noise (I've never checked it to verify its "whiteness"). The noise floor was higher, and the S/N ratio was therefore lower.
    – Warrior Bob
    Sep 11, 2012 at 16:45
  • Yeah, that's what I mean. I can't think of any reason why that would happen, if it's just 1 cable vs a chain of several cables of the same overall length.
    – endolith
    Sep 11, 2012 at 17:34

A connection adds contact noise and has worse common noise injection characteristics than the cable proper. Also even the best connection has a mismatch to the line impedance of the cable and thus every connection is a point where the signal gets reflected. Now 40kHz has a wavelength of 7.5km in air and probably 80% of that in cable, so you are unlikely to get significant comb filter effects within the recordable (let alone audible) range. So probably the added noise is the main problem and the reflection issue mostly irrelevant.

To get an estimate, try switching your mobile to airplane mode and back (or off and on again) near the cable and either close or far from the next connection. It's unlikely that you won't hear it chattering with the next mobile tower either case, but the volume might well differ.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.