A violinist friend of mine is planning to buy this pickup, Fishman V-200, for his acoustic violin.

Can it be hooked directly to a mixer for recording or live performance? Or, do we have to add a preamp/DI box to the chain to get a rich, full tone?

I'm familiar with standard electric guitar setups like miking the amp and DI box->Amp model.

What will be the standard setup for violin with this piezo pickup?

2 Answers 2


According to the user guide, the manufacturer recommends a 10M ohm impedance preamp. That's a very high impedance, which might even exceed the guitar/"instrument level" input on some mixers (contrast with "line level" and "microphone level").

The short answer is that unless your mixer has a matching high-Z input, then the violin is going to sound thin in a manner very similar to your experiences with electrical guitars. It'll work in the sense that you can get a signal from the violin pickup, but you probably won't like the result. Updated: A regular DI unit might not have a high enough impedance, since electric guitar pickups are in the 20K to 40K range. For maximum flexibility, your friend should consider getting a DI unit with an input impedance that matches the pickup.

Here's a good overview of impedance in relation to sound recording. According to this, the Fishman V-200 is a high-Z source. It's okay to connect a low-Z source to a high-Z input, but the opposite has consequences:

If you connect a low-Z source to a high-Z load, there is no distortion or frequency-response change caused by this connection. But if you connect a high-Z source to a low-Z load, you might get distortion or altered response. For example, suppose you connect an electric bass guitar (a high-Z device) into an XLR-type mic input (a low-Z load). The low frequencies in the signal will roll off, so the bass will sound thin. We want the bass guitar to be loaded by a high impedance, and we want the mic input to be fed by a low-impedance signal. A direct box or impedance-matching adapter does this.

(emphasis mine)

I don't have any experience with the Fishman V-200 pickup, but trying to plug in electric guitars and basses into low-Z inputs is a pretty common problem that a lot of musicians have run into at some point. Without the Internet, or some knowledge of electrical engineering, the result can be pretty baffling :-)

  • Thanks Kim, for the detailed info. There's a possibility that acoustic instrument piezo pickup might produce a more usable output than electric guitar/magnetic pickup as we know. I'm only guessing, haven't tried yet.Fishman suggests its G II preamp, which has a 1/4" input and a 1/4" output. Its manual says the preamp can be connected to an Amp or DI (why again? Should I get one to use with this preamp), or mixer (unbalanced Mic input). Or there's another more expensive preamp with XLR output. I couldn't decide whether to suggest one of these (volume/tone control!) or a DI. Commented Feb 27, 2011 at 19:30
  • The recommend 10 million ohm impedance really stood out to me, though. I've seen the impedance of electrical guitar pickups quoted around 20K to 40K ohms. I think the low end of a violin doesn't come anywhere close to the deep E string on an electric guitar, but still, I imagine there must be a fairly significant roll-off in the low end when connecting to a low-Z input with this pickup. I guess your best bet is to try before you buy?
    – Kim Burgaard
    Commented Feb 27, 2011 at 19:38
  • I just looked at the G-II product page. It transforms the impedance from 10M to a much more usable 3.5K, but the output is still not balanced. So I think they're just saying you have the option of using the G-II together with a DI unit to get both; the impedance step-down as well as running the signal into the mixer through a balanced connection. A regular DI unit will probably have an impedance lower than 1M, so that's why you need the G-II even with a DI
    – Kim Burgaard
    Commented Feb 27, 2011 at 19:45
  • Try before buy- not possible here :( I have a DI (samson s-direct), will run some tests. "...you need a GII even with a DI"? I was wondering do I need the DI if I get G-II. Unbalanced -> mixer, not good? Commented Feb 27, 2011 at 20:00
  • G-II -> mixer should work great over shorter distances and if you don't have problems with hum
    – Kim Burgaard
    Commented Feb 27, 2011 at 20:06

I use a Fishman v100 with their 3 band eq/preamp. Plugging the preamp directly into a Fender guitar amp hiZ input (1/4") is not giving me good sound. It is "crackling" or "glassy" for want of better words.

Using a DI box (passive) and going directly to the mixer works well.

I want to try the new Fishman Loud Box amplifiers though. I think that might be the best solution. I've heard a guitar played through the smaller one and it sounded great, but I havn't yet tried the violin. We'll see.

Friday 11/4 I tried the Loud Box mini amplifier. It was terific (I bought it). Very clean sound and more power than most will ever need. I would recommend this set-up to anybody looking for faithful reproduction of their violin's sound. Incidentally, the V-100 pickup is the same as the V-200 except it has a 1/8" jack compared to the V-200's Carpenter type 1/4" jack.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.