Take the 2-minute tour ×
Sound Design Stack Exchange is a question and answer site for sound engineers, producers, editors, and enthusiasts. It's 100% free, no registration required.

In order to eliminate clicks in words in Pro Tools, and I use either the Pencil Tool or cut out a cycle of the waveform.

What would software tool would you recommend?

share|improve this question
add comment

11 Answers 11

up vote 10 down vote accepted

I'm all about iZotope RX. It's such a lifesaver for me. I do everything from lowering the noise floor on recordings, removing clicks and clipping, to removing a cough from a live music performance (I actually got that one to work perfectly!! I'll have to see if I can find the original and final to let you guys A/B the two).

iZotope RX

If it's something really tiny and don't want to spend time in RX (it can be very time consuming for more complex fixes), I'll go with the old pencil tool trick.

share|improve this answer
    
Thanks a bunch! So Izotope RX will take clicks out of a voice without artifacts? –  Utopia May 6 '10 at 16:27
    
+1 for RX, the projectsaver. –  Josh McHugh May 9 '10 at 14:52
    
+1 for RX. Amazing tool. And the ProTools Pencil! Love it :) I use the wacom tablet to do editing... much easier (once you get used to it)! –  Davide Favargiotti May 12 '10 at 8:49
    
Hi! Could you please post some video about editing by tablet? Thanks a lot because I can't find anything about it...do you think that a tablet could work even with other sequencer as Nuendo, Cubase or Samplitude? thanks! –  Francesco Lucarelli Jun 1 '10 at 9:41
    
+1 again for RX - since I brought I have used it in some capacity everyday :) –  RedSonic01 Oct 26 '10 at 9:02
add comment

Try these:

Waves X-Click and X-Crackle

Izotope Rx

Note: Izotope has a full-featured demo that you can audition before you buy to see if it will work for your needs.

Waves X-Click Waves X-Crackle

share|improve this answer
    
I have X-Click but can't get it to not artifact a voice. Have you had any luck using it on a voice to remove mouth noise? –  Utopia May 14 '10 at 1:14
add comment

I started out with the pencil tool like the other guys until where I work bought iZotope RX. To clean up clicks etc it is an amazing tool and worth every penny if you can buy it.

share|improve this answer
    
On voice as well? I am such a stickler for quality of the voice and I hate to add artifacts to it if I can avoid it. So, would you even use Izotope RX on a featured voice-over that is louder than everything else? –  Utopia May 6 '10 at 16:41
    
Obviously if removing the click entirely lessened the quality of the voice I wouldn't. Sometimes I meet a compromise if the noise affects the enunciation of the voice. Sometimes it is preferable to leave the click in as to remove it would be too destructive on the performance. It's about choices. The enunciation comes first, then sound quality of the voice in my books. –  ianjpalmer May 7 '10 at 8:25
add comment

I check if the job can be done with iZotope RX. It works very well. If I have more serious problems I use the pencil tool in Sony Sound Forge.

share|improve this answer
add comment

Editing out a cycle using protools in shuffle mode is efficient. Unless you are working with picture.

I switch to the Pencil tool only when the above method doesn't cut the mustard.

share|improve this answer
    
That's exactly what I do! –  Utopia May 6 '10 at 21:35
add comment

When i really want to get that click out manually, i cut and paste. Each phoneme tends to have a repeating wave cycle, so i zoom in til i see the wave and grab one of the cycles before or after, and paste it over. A small crossfade may be necessary. The pencil tool only lowers the amplitude of the click, it doesn't completely get rid of it.

It's only really good for glitchy clicks, as clicks recorded in the space will have a reverb tail.

share|improve this answer
add comment

Slice out the click, then cut and time stretch (TCE) the region before to cover the whole and xfade.

share|improve this answer
add comment

Pencil or cycle copy-paste for me...

share|improve this answer
add comment

For quick "one click" click removal, the old Sonnox Declicker is outstanding - haven't used their new one, though...

For "musical clicks" I like to use iZotope's Spectral Repair - amazing flexibility in certain situations.

Can't beat good old room tone fill for a lot of clicks... it all depends on the time you have and the "type" of click you're dealing with.

share|improve this answer
add comment

Unfortunately, I don't have the budget to try out any nice plugins, but pencil tool in a pinch.

share|improve this answer
add comment

If editing in Protools then I'll mainly cut out cycles over using the pencil tool, but I'll use that if needs be. If I'm working to picture, then I just take a little more time to check that the sync's not been compromised. After all - picture work is mainly FPS and cutting out a cycle is tiny samples.

If I have a really clicky piece then I'll use Audition as I've recently been introduced to the spectral editing tool which is, on one hand, cheating (ie not using your ears) and on the other as fast as lightning.

I'll have a proper look into XClick though :)

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.