Take the 2-minute tour ×
Sound Design Stack Exchange is a question and answer site for sound engineers, producers, editors, and enthusiasts. It's 100% free, no registration required.

Hello guys. I'm having an issue with using compressors for voice recordings, namely when two voices vary wildly. For example, If a speaker's voice peaks at -20dB and another one's at -1 dB, no matter what compressor settings I use, in the end there still is a big difference in the perceived loudness of the voices.

The only solution that I found so far is to manually raise the volume only on the soft parts. However, this is time consuming and I'm looking for an automated process that can take care of this. Can you guys think of one?

share|improve this question
add comment

6 Answers

Try and match the RMS (Average) levels and don't worry about the peaks as long as they are below a sensible limit.

If you are using PT go to the gain plug-in, and you can find the RMS level there.

What I usually do is find a region that I consider to be dynamically perfect for the section I am working on, i.e. just the right balance between RMS and peak. You don't need to be too precise with the RMS match, within 2 or 3 dBs is usually fine.

I will then try and replicate the dynamic range on the problem regions using a compressor and make-up gain. So if the dialogue involves whispering and shouting, then the difference between the RMS and peak will obviously be greater, or if the dialogue is supposed to be monotonous, then the difference between RMS and peak will be much less.

share|improve this answer
add comment

The way i do it is to ride the faders to balance things before going into eq, de-esser and compressor. Then i put a Brickwall limiter on the submaster and master. It's timeconsuming, but it's worth it.

You could try the Waves Vocal Rider plug if time is more important than quality in this case.

share|improve this answer
add comment

have a think about the characters, sometimes they're supposed to vary like that.

up the gain on the quieter voice before compression, lower the gain on the louder before compression. find a place to insert an EQ on each, before compression. then have a think about the microphones used. on the louder voice you may need just to shave the peaks off, whereas on the quieter you would be less subtle. watch out for noise, and don't look at the meters too much.

share|improve this answer
    
Sorry for not specifying from the get go. This is not for film, it's for radio or podcasts, and the aim is to have little variation between speakers in loudness. –  George V. Aug 25 '12 at 6:31
    
conversationsnetwork.org/levelator The levelator is very popular for podcasts –  Iain McGregor Aug 25 '12 at 16:39
    
Thanks for the suggestion, Iain. But the Levelator looks like a newb tool, mainly for the lack of controls or parameters. –  George V. Aug 26 '12 at 4:46
    
Did you try it? It's a surprisingly effective maximizer for spoken word. –  MtL Aug 26 '12 at 5:49
add comment

You could try an automatic gain rider, e.g. http://www.meldaproduction.com/mautovolume/ and adjust the settings for the two tracks by ear.

share|improve this answer
add comment

You could also try an upward/parallel compression approach. Dupe the "too quiet" audio onto a second track, add a compressor with a low threshold and high ratio (so that it's really compressing the hell out of the dialog), fast attack, slow release, and slap on some heavy make up gain. What you're left with is the a track full of the lower end of the dynamic range. Route the original and the parallel compression to an aux channel and mix them to taste (you'll probably only use a little of the parrallel track). Make sure you don't have any phase/timing issues being introduced by the plug-in, adjust the timing of the parallel track if you do. This should help add some body to a weak track. If any additional compression is needed, add it to the aux track the two copies are being mixed to.

share|improve this answer
add comment

It has already been mentioned, but its an amazing (Pricey) tool. If you go through this often, then this will make your life so simple.

http://www.waves.com/content.aspx?id=9945

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.